Peerless Combi 160 Price: Typical Purchase and Installation Cost 2026

The Peerless Combi 160 price depends on whether buyers install it as a direct replacement, a retrofit, or a new system; typical total costs include the unit, parts, labor, and any required piping or vent changes. Buyers usually see a unit price plus installation with common ranges listed below to help budget for this combi boiler or comparable near-condensing package.

Item Low Average High Notes
Unit Only (Peerless Combi 160) $1,200 $1,650 $2,200 Assumptions: new, standard warranty, no controls.
Installation (labor + basic parts) $900 $1,700 $3,200 Assumptions: typical home, accessible utility room.
Total Installed $2,100 $3,350 $5,400 Assumptions: Midwest labor, moderate piping work.
Replacement Only (labor, remove old) $600 $1,200 $2,000 Assumptions: same footprint, existing venting usable.

What Buyers Pay For A Peerless Combi 160 Installed

Typical installed price for a Peerless Combi 160 ranges from $2,100-$5,400 depending on job complexity; the average installed cost is about $3,350. Most homeowners pay $1,200-$2,200 for the unit and $900-$3,200 for installation and parts.

Assumptions: 1-2 bathroom single-family home, 80-120 gallon equivalent hot water demand, accessible mechanical closet.

Breakdown Of Major Quote Parts: Materials, Labor, Equipment, Permits

A clear parts breakdown helps compare quotes and spot markups; the table below shows typical ranges by component for this combi boiler job.

Materials Labor Equipment Permits
$600-$1,200 (valves, piping, controls) $600-$2,400 () $200-$800 (flue, condensate neutralizer, pump) $0-$300 (local permit/inspection)

Materials and labor together typically account for 70%-85% of the installed price.

How System Specs And Home Conditions Change The Final Price

Three strong drivers that change a quote: number of fixtures served, venting distance/type, and whether the combustion air route must be modified. Each additional bathroom or high-flow demand can raise required capacity and cost by $300-$900.

Call 888-906-9139 – Get Your Free HVAC Quote & Save More Today!

Specific thresholds: if run length for new stainless venting exceeds 10-15 feet, add $150-$500; if condensate neutralizer is required (shared sewage rules), add $75-$250. Assumptions: local code, typical single-family layout.

Concrete Ways To Reduce Peerless Combi 160 Price On Quotes

Buyers can lower costs by retaining existing piping runs, scheduling replacement in off-season, and choosing standard controls instead of high-end smart panels. Keeping plumbing stub locations and flue termination unchanged often saves $400-$1,200.

Other tactics: get at least three itemized quotes, accept contractor-supplied common-brand parts instead of OEM extras, and combine with simultaneous projects to reduce mobilization fees.

Regional Price Variations Across U.S. Markets

Labor and permit differences shift installed cost: expect 10%-25% higher prices in Northeast and West Coast metros versus Midwest and South. A $3,350 average in the Midwest could be $3,700-$4,200 in urban Northeast markets.

Rural areas may have lower rates but higher travel or minimum-charge fees; add 5%-15% for contractors traveling over 30 miles or when a service truck minimum applies.

Typical Job Time, Crew Size, And Labor Rates For This Install

Install time for a straightforward Peerless Combi 160 swap is typically 4-12 hours with 1-2 technicians; complex retrofits can take 1-3 days. Hourly rates vary $75-$125 per hour; expect 8-18 labor hours on most installs.

Call 888-906-9139 – Get Your Free HVAC Quote & Save More Today!

Example: 10 hours × $95/hr = $950 labor plus parts and equipment.

Add-Ons, Removals, And Permit Fees That Often Appear On Estimates

Common extras that raise the final invoice: old unit disposal ($75-$250), electrical upgrades ($200-$900), new condensate pumps ($150-$450), and boiler board or seismic strapping in some jurisdictions ($50-$300). Budget an extra $300-$1,000 for typical add-ons beyond the base quote.

Permit and inspection fees are often $0-$300 depending on local requirements; failure to permit can increase long-term costs if corrections are required.

Scroll to Top