Goodman Furnace Pressure Switch Location and Troubleshooting

The pressure switch is a small but critical safety device on a Goodman furnace that confirms proper venting and inducer motor operation before the furnace lights. This article explains where the pressure switch is typically located, how to identify and test it, common issues tied to its placement, and steps for safe troubleshooting and replacement.

Topic Quick Answer
Typical Location On or near the draft inducer assembly, connected to a PVC vent or inducer housing with vacuum tubing
Appearance Round or rectangular switch with two vacuum ports and two electrical terminals
Common Symptoms No heat, ignition lockouts, error codes (pressure switch fault), inducer runs but furnace won’t light
Basic Test Visual check, listen for inducer, test continuity with multimeter when inducer runs, measure vacuum with manometer
Replacement Complexity Moderate; accessible on many Goodman units but requires power off and careful tubing/terminal reconnection

What The Pressure Switch Does

The pressure switch confirms the inducer fan and venting system create the proper airflow and pressure before the furnace burner ignites. It prevents combustion when drafts, blockages, or vent leaks are present.

Pressure Switch Function: When the inducer motor runs, the switch senses a negative or positive pressure (depending on design) and closes an electrical circuit to the control board allowing ignition to proceed.

Where To Find The Pressure Switch On Goodman Furnaces

On most Goodman furnaces, the pressure switch is mounted on or adjacent to the draft inducer assembly near the flue or PVC vent connector. It sits between the inducer housing and the control board with vacuum tubing linking it to the inducer or vent collar.

Common mounting positions include the inducer housing cover, the furnace cabinet wall near the vent collar, or on a small bracket along the intake/vent piping. It is usually easy to spot because of the vacuum tubing attached to one or two small nipples on the switch.

How The Pressure Switch Looks

The pressure switch typically appears as a round or square plastic device roughly two to three inches wide. It has one or two small vacuum ports (plastic nipples) and two terminal screws or spade connectors for wiring.

Call 888-906-9139 – Get Your Free HVAC Quote & Save More Today!

Some Goodman models use a metal-bodied switch but the presence of vacuum tubing and terminal wires is the identifying feature. Labels or markings will often include a model or pressure rating in inches of water column (in. WC).

Model Variations And Location Differences

Different Goodman lines (GMVC, GMP, GMUH, GMES) may place the pressure switch in slightly different spots, but it remains associated with the inducer motor and venting system. High-efficiency condensing units may have additional pressure switches for condensate traps or negative pressure sensing.

Key Variations: Some units have two pressure switches—one for pre-ignition inducer validation and another for secondary vent checks. Location remains near the inducer or PVC vent runs.

Symptoms Indicating Pressure Switch Problems

Common symptoms include the furnace trying to start but locking out, error codes such as flashing LEDs indicating pressure switch faults, the inducer fan running without ignition, and inconsistent heating cycles.

Other signs include visible crack or wear in vacuum tubing, slow inducer motor spin, blocked vent/condensate traps, or a switch that fails to click when the inducer runs.

Safety Precautions Before Inspecting

Always turn power off at the furnace switch or circuit breaker before touching components. Gas valves should be closed if performing deeper disassembly. Use insulated tools when working near electrical terminals.

Call 888-906-9139 – Get Your Free HVAC Quote & Save More Today!

If unfamiliar with gas or electrical work, it is safest to contact a licensed HVAC technician. A pressure switch is a safety device; incorrect handling can create hazardous conditions.

Step-By-Step Visual Inspection

Turn power off and remove the furnace access panel to locate the inducer assembly. Identify the pressure switch by looking for a small device with vacuum tubing and two wiring connections.

Inspect the vacuum tubing for cracks, kinks, or disconnections. Examine the tubing fittings for loose clamps. Check for soot, water, or blockages in the vent pipes that could prevent proper pressure creation.

Electrical And Continuity Tests

With the furnace powered and the inducer running (fan starts during a call for heat), the switch should close and show continuity between its two terminals. Use a multimeter set to continuity or ohms to verify closure.

Test steps: restore power, set thermostat to call for heat, observe inducer start, measure across the two switch terminals—continuity indicates a closing switch. No continuity while inducer runs signals a faulty switch or pressure problem upstream.

Measuring Pressure With A Manometer

A manometer provides the most accurate test. Connect the manometer tubing to the pressure port on the switch or to the inducer housing; compare readings to the furnace specifications listed on the unit or in the technical manual.

Typical Values: Pressure switches often operate in the range of 0.01 to 0.5 inches of water column depending on furnace design. Refer to the furnace label for exact setpoint values.

Common Causes Of Pressure Switch Failures

Failures often stem from blocked or restricted venting due to debris, animal nests, or snow; damaged vacuum tubing; failed inducer motors; clogged condensate traps; or internal switch wear and failure.

Environmental factors such as freezing condensate lines, crushed PVC vent runs, or improper venting slope can cause intermittent pressure readings and nuisance trips.

Troubleshooting Guide

  • Check vacuum tubing for damage and replace if cracked or brittle.
  • Inspect and clear vents, flue, and condensate traps of debris or ice.
  • Ensure inducer motor runs at full speed and bearings are not seized.
  • Verify proper electrical connections to the pressure switch terminals.
  • Use a manometer to confirm pressure at the switch meets manufacturer specs.

Replacing The Pressure Switch

Replacement is a moderate DIY task for those comfortable with basic furnace work. Turn power off, note wiring positions, remove vacuum tubing and electrical connectors, unmount the old switch, and install the new one in the same location.

After replacement, reconnect tubing and wiring exactly as removed, restore power, and test operation. Use the new switch with identical pressure rating to the original unit for correct performance.

Costs And Parts

Typical OEM or universal pressure switches range from about $20 to $80. Labor for professional replacement averages between $100 and $300 depending on local rates and accessibility.

Always choose a replacement with the proper pressure setpoint and matching terminal configuration. Using the furnace model number helps locate the correct part.

When To Call A Professional

Call a licensed HVAC technician if the inducer motor fails, if venting problems are suspected, if the pressure switch location is hard to access, or if there is a gas-related concern. Professionals can diagnose complex venting issues and ensure safe repairs.

Immediate Help Needed: If there is a persistent gas smell, frequent lockouts, or visible damage to vent pipes, stop using the furnace and contact a professional immediately.

Maintenance Tips To Prevent Pressure Switch Issues

Perform annual furnace maintenance including vent inspections, filter changes, and inducer motor checks. Keep outdoor vents clear of snow, leaves, and debris to maintain proper airflow.

Inspect vacuum tubing during routine servicing and replace it if it shows any signs of aging. Schedule a professional tune-up each heating season to catch early signs of pressure-related faults.

FAQs

Can A Dirty Filter Cause A Pressure Switch Fault?

A very dirty filter can reduce airflow and indirectly affect combustion dynamics, but pressure switch faults are more commonly linked to venting, tubing, or inducer problems rather than the filter alone.

Is The Pressure Switch Repair Covered Under Warranty?

Coverage depends on the furnace warranty terms and age. Manufacturer warranties may cover defective switches under specific conditions; installation or environmental damage is usually excluded.

Can The Furnace Run Without A Pressure Switch?

No. The pressure switch is a required safety interlock. Removing or bypassing it creates a dangerous condition and is not recommended or code-compliant.

References And Further Reading

Goodman installation and service manuals provide model-specific pressure switch locations and specifications. HVAC technical training materials and manometer guides offer detailed testing procedures.

For precise part numbers and pressure setpoints, consult the label on the furnace and the Goodman product documentation or contact a licensed HVAC professional.

Scroll to Top