Comfortmaker Furnace Reset Button Guide: Locate, Use, and Troubleshoot

Comfortmaker Furnace Reset Button searches often reflect urgent homeowner needs when a furnace stops working. This guide explains what the reset button does, where to find it, safe reset procedures, troubleshooting steps, and when to call a professional. It helps readers quickly diagnose common issues and decide whether a simple reset will restore heat or if further service is needed.

Issue Reset Action When To Call A Pro
No heat, fan running Press reset after 10-minute cool-down If repeated resets required
Short cycling Check filter, thermostat, press reset If persists after maintenance
Ignition failure Reset once, then monitor If error codes or no ignition

What The Comfortmaker Furnace Reset Button Does

The Comfortmaker furnace reset button is a safety and control feature found on many gas and electric furnace models. It clears certain electronic lockouts and restarts control circuits after failures such as ignition problems, flame sensing errors, or safety trips. Pressing the button initiates a controlled restart sequence to attempt normal operation.

Where To Find The Reset Button On Comfortmaker Furnaces

Location varies by model, but common places include the furnace control panel, near the gas valve, or inside an access compartment. Some newer Comfortmaker units use an electronic control board with a recessed reset switch or require power cycling, while older units may have a prominent red or black push-button labeled “Reset” or “Limit Reset.”

How To Identify The Button

Look for a small push-button, often recessed to avoid accidental presses, labeled RESET, LIMIT, or PILOT RESET. If the button is not obvious, consult the furnace’s user manual or the model number sticker on the cabinet to download the manual from Comfortmaker’s website.

When It Is Appropriate To Use The Reset Button

Pressing the reset button is appropriate after an isolated malfunction such as a single ignition failure, a temporary flame rollout, or a sensor fault that has likely cleared. It is not a substitute for repairs when underlying faults persist. If a reset resolves the issue once, it may be acceptable; repeated need for resets indicates a deeper problem.

Safety Considerations Before Resetting

Always follow safety precautions: turn off power to the furnace at the thermostat or breaker when accessing panels, ensure gas is shut off if working near the valve, and wait at least five to ten minutes after shutdown to allow combustion components to cool. If there is a smell of gas, leave the premises and call the gas company or emergency services.

Call 888-906-9139 – Get Your Free HVAC Quote & Save More Today!

Step-By-Step: How To Reset A Comfortmaker Furnace

This procedure is general and may vary by model; refer to the specific user manual for model-specific steps. The steps below provide a safe, systematic approach to resetting a Comfortmaker furnace control.

  1. Turn Off Thermostat Call For Heat: Switch the thermostat to OFF and set the fan to AUTO to stop the control signals.
  2. Power Down The Furnace: Turn off the furnace power using the service switch or the circuit breaker to de-energize the controls.
  3. Wait Ten Minutes: Allow time for the control board and gas valve to fully reset and for any residual gas to dissipate.
  4. Locate The Reset Button: Remove the access panel if needed and identify the reset button or switch on the control board or near the gas valve.
  5. Press The Reset Button Once: Press and release the reset button. Do not hold it for extended periods unless instructed by the manual.
  6. Restore Power And Thermostat: Close the access panel, turn the furnace power back on, and set the thermostat to the desired heat setting.
  7. Observe Operation: Allow the furnace to run through a full ignition cycle and watch for normal operation or error codes on the control board.

Troubleshooting If Reset Does Not Fix The Problem

If a single reset fails to restore normal operation, follow these diagnostic steps. Many issues that appear to require a reset are caused by easily identified faults that can be corrected safely.

Check The Air Filter And Airflow

A clogged filter or blocked vents cause overheating and can trigger safety shutdowns. Replace or clean the filter and ensure supply and return vents are open and unobstructed. Poor airflow is a primary cause of limit trips that prompt resets.

Inspect The Thermostat

Confirm thermostat settings, battery condition, and wiring. A malfunctioning thermostat can send incorrect signals resulting in no ignition or short cycling. Replacing batteries and testing different temperature settings helps isolate thermostat issues.

Examine Ignition Components

Ignition failure can result from a faulty hot surface ignitor, pilot assembly, or flame sensor. These components can be tested visually or with simple resistance checks. If the ignitor is cracked or the flame sensor is coated with residue, cleaning or replacement may resolve the problem.

Look For Error Codes And Control Board Lights

Comfortmaker control boards often use LED blink codes to indicate specific faults. Count blink patterns and cross-reference with the manual to identify the root cause. Document any error codes before calling for service.

Call 888-906-9139 – Get Your Free HVAC Quote & Save More Today!

Check The Gas Supply

Ensure gas valves are open and that other gas appliances operate normally. If there is low gas pressure or an interrupted supply, the furnace may fail to ignite. Contact the gas utility for suspected supply issues.

Common Causes That Lead To Reset Button Use

Understanding common causes helps avoid unnecessary resets and promotes timely repairs. Typical triggers include thermostat issues, dirty filters, blocked condensate drains on high-efficiency units, faulty flame sensors, failed ignitors, and electrical problems like loose wiring or control board faults.

When Repeated Resetting Means It’s Time To Call A Professional

Repeated need to press the reset button, persistent error codes, strange odors, gas smell, or visible damage indicate a problem beyond simple homeowner maintenance. In these cases, contacting a licensed HVAC professional is recommended to diagnose and repair safety-related issues.

Signs To Call A Professional

  • Multiple resets required within a short period
  • Persistent error codes on the control board
  • Unusual burning smells, loud noises, or flame rollout
  • Gas odors or suspected leaks
  • Visible damage to electrical components or gas valve

Maintenance Steps To Reduce Resets And Improve Reliability

Regular maintenance lowers the chance of control lockouts and improves furnace longevity. Suggested maintenance includes filter replacement every 1–3 months, annual professional tune-up, cleaning the flame sensor, checking the condensate drain on condensing furnaces, and inspecting vents and ductwork for obstructions.

DIY Maintenance Checklist

  • Replace or clean air filters monthly during heavy use
  • Vacuum around the furnace cabinet to reduce dust buildup
  • Inspect venting for blockages or animal nests
  • Check thermostat batteries and settings seasonally
  • Observe furnace operation during startup for irregularities

Model Differences And Manufacturer Guidance

Comfortmaker model lines vary in control layout and reset procedures. Some modern units use electronic touchpads with diagnostic menus rather than physical reset buttons. Always consult the model-specific manual or Comfortmaker technical support before attempting advanced diagnostics.

Where To Find Manuals And Technical Support

Comfortmaker documentation and troubleshooting guides are available on the manufacturer’s website and through authorized dealers. Recording the furnace model and serial number will speed support interactions and ensure correct parts or procedures are recommended.

Safety And Legal Considerations

Gas furnaces involve combustible fuel and high-voltage components. Improper repairs can create safety hazards and may violate local codes or warranty terms. Homeowners should limit work to basic maintenance and resetting; any work involving gas lines, burners, or electrical components should be performed by licensed technicians.

Frequently Asked Questions About The Comfortmaker Furnace Reset Button

How Many Times Can A Furnace Be Safely Reset?

Occasional resets after isolated events are generally safe. However, repeated resets are a warning sign and should prompt inspection. Persistent resets may indicate a failing component or unsafe condition requiring professional service.

Will Pressing The Reset Button Void The Warranty?

Using the reset button as instructed in the user manual typically does not void warranties. Performing unauthorized repairs or tampering with sealed components can affect warranty coverage. Always follow manufacturer recommendations and document any service performed.

Is Resetting The Same As Power Cycling?

Resetting a dedicated button performs a targeted restart of control circuits. Power cycling the furnace by turning off the breaker achieves a broader reboot. Both can clear temporary lockouts, but control-board resets and power cycles are not identical in effect.

What If The Furnace Shows An Error Code After Reset?

Document the error code and consult the manual for the specific meaning. Codes often point to sensors, flame detection, or communication faults. Provide the code to a technician to accelerate diagnostics and repair.

Finding A Qualified Comfortmaker Technician

Choose a technician certified for Comfortmaker or its parent company brands. Verify licensing, insurance, and references. Ask about experience with specific model types and request a written estimate for repairs. Maintenance agreements can provide annual inspections that reduce emergency visits.

Questions To Ask A Technician

  • Are you licensed and insured?
  • Do you have experience with Comfortmaker systems?
  • Can you provide an itemized estimate and warranty for repairs?
  • Do you offer maintenance plans and safety inspections?

Using the Comfortmaker Furnace Reset Button can resolve some temporary faults but should be used judiciously and as part of a broader approach to furnace maintenance and safety. When in doubt, document the issue, avoid repeated resets, and call a qualified HVAC technician to protect home safety and system reliability.

Scroll to Top